pikebomb6

Patio Doors Repairs Patio doors give homeowners sunlight and fresh, clean air. They also enhance the value of homes. But with time, they may cause issues that must be addressed swiftly. Understanding how patio doors work can help homeowners communicate better with contractors about problems they face. Here are some common patio door repairs:. Rollers that are not aligned Sometimes the sliding patio door will get stuck and it's not simple to get the thing to open again. Most of these sluggish sliding patio doors can be fixed easily with a bit of oiling and cleaning, unless a structural issue is present. Typically dirt on the lower track can cause the bottom track and rollers to become misaligned. In this case it is necessary to clean the track and apply a thin coating of lubricant to let the rollers move easily. It can also be caused by wear or damage to the hinges that connect the doors that house a portion of these rollers, springs (whether torsion or extensions); and cables which lift the door. These components, when damaged or worn, can alter the alignment of rollers and cause resistance, as well as other problems, such as a heavier feeling door or higher energy consumption. patio doors repairs and inspections by a professional will ensure that these elements are in good working order to keep your patio doors operating smoothly. To check roller-to-roller alignment to determine alignment, set up an eagle's foot at the one end of the track. use a tramming stick to sweep across both rollers, recording the distance they travel. Repeat the process on the other end of the track, and divide by 2 to obtain a reading of the rollers' parallelism (Photo 1). This method is not as precise as using pi tapes to measure diameter directly, but it's much more efficient and less time-consuming than measuring each individual rail with a level or carpenter's level. You can also check the alignment of the rollers by taking off the head stop. This is an elongated plate that is located in the bottom of the door jamb. It stops the rollers. This requires the removal of any grilles or shades that are removable, and in the event that the door is heavy, you should seek assistance with this step. After the head stop is removed, carefully remove the screws that adjust the head track by removing them with the help of a screwdriver. Then, reinstall the assembly by aligning each roller adjustment screw with its access hole and tapping it in using a hammer. Dirty or damaged tracks Sliding patio doors are magnets for dirt, debris and other elements outside. They are also prone to misalignment and other issues that require professional repair. In order to extend the life of your patio door, finding and fixing these issues promptly is crucial. Dirty tracks are among the most frequent causes of problems with sliding patio doors. Over time, dirt, food crumbs, pet hair and yard debris could get stuck in the small spaces of your sliding door track, causing the door to snag or become difficult to open. To avoid problems like this it is recommended to sweep and clean your patio door tracks once per month. You can clean your patio door tracks using a non-abrasive cleaning solution, or use warm soapy tap water after you've removed any loose debris. If you notice that certain parts of the track are more difficult to clean, you can try using a butter knife or an old toothbrush to clean these tiny spaces. It is also important to grease the tracks regularly to avoid your sliding door from becoming stuck or difficult to open. If you have Panda patio doors it is recommended that you add silicone spray to the bottom track on a regular basis. You can also rub paraffin wax on the track to enhance glide. Air leaks or drafts can also affect your sliding patio doors. This could happen if the weather stripping of your sliding patio door has worn away or has been damaged. This can lead to an opening between your sliding patio door and the frame. This lets air in and decreases the efficiency of energy. Check that your weatherstripping is in good condition and replace it when needed. If you use it regularly, your patio door will show normal wear and wear and tear over time. These issues aren't usually an indication of a serious issue. In the majority of cases, minor repairs can help extend the lifespan of your patio door and ensure it is operating properly. Get a professional in touch to fix any issues as soon as they occur to prevent costly repairs in the future. Glass that is cracked or warped A patio door that is damaged or sagging is a real eye-sore and can pose an security risk. This could also allow unwanted animals into your home and cause the temperature to fluctuate. Fortunately, these issues are usually simple to fix if you catch them early. First, a quick glance at the glass can determine the type of repair is required. Cracks in glass are usually caused by stress or impact. They are more difficult to repair than chips on the surface. A professional may have to replace the lead on this panel. This will require the removal of the glass, cleaning it, and replacing the broken pieces. To do this, a professional will need accurate documentation of the glass in its original form to aid in comparing the new glass to the original. Sometimes cracks in glass can be filled with epoxy plastic. This can be purchased from hardware stores or the home improvement section of many stores. A professional will typically use a soldering iron to melt the plastic, then apply it to the cracks in the glass. After the plastic has cooled and the professional has removed any excess. If the crack in the glass isn't too big, there might be a chance to repair it with clear sealant. You can purchase this type of product from any hardware retailer. It is important to dry the crack completely before applying sealant. This will stop the repair from failing. You can speed up the process by using a hair dryer or a different fan. Weatherstripping damaged A weather stripping that is worn out not only looks ugly and is a security risk, but also allows outside air and heat to escape. A simple fix using a new piece of weather stripping can save you money while keeping your home more comfortable. First, ensure you have all the tools and supplies. You'll need a replacement weather-stripping kit or adhesive/caulk sealing agent (depending on the repair method you choose) as well as pliers and scissors, a utility knife as well as protective gloves or goggles and a replacement weather-stripping kit. Remove the old weather stripping, by cutting through the end piece and pulling it up using any screws that are attached, if appropriate. Then take care to remove any pieces still left in the pliers or pry bar. Begin by measuring the space around the door frame. You can use the measurements to determine the size of weather stripping that you need. Make sure you leave a bit of extra length so that you can adjust the size later. Once you've got the right size, apply the backing and press the material against the frame. If you want, secure it to the frame using small nails or hammers. Apply wood filler to the frame to cover any divots or holes. Let the filler dry completely before painting. It is recommended to use oil-based paint, however, latex can also be used. Lastly, make sure to clean your tracks and sliding doors regularly. Making the effort to do this can prevent the doors from sticking and other issues later on. Making sure you are keeping up with maintenance and repairs to your patio doors will ensure they remain functional, attractive and energy efficient. By doing so you can enjoy the great outdoors with confidence, and save money at the same time! Enjoy your home renovation projects!